2 x 120 Watt Sinewave Power Amplifiers
The SPA (Security Power Amplifier) is primary designed for integration into Voice Alarm systems, but thanks to its flexibility, it can also be used for any Commercial application.
The SPA amplifiers were specifically developed to meet the requirements of EN 60849 for safety installations. Each amplifier module is fitted with its own 220 VAC/24 VDC power supply for increased system reliability.
To avoid handling errors, the volume output is set using the potentiometer located at the rear of the amplifier. Further to standard protection via fuses, SPA amplifiers also have electronic and thermal protection to protect them from potential hazards.
A ventilator provides forced cooling for the final power shelves and internal parts of the amplifier. It starts up automatically when the heat shunt reaches a certain temperature threshold, and stops when the temperature returns to normal values. Four LEDs display the status of each amplifier: AC or DC power supply, Line Overload and Temperature overload. Furthermore, a three LEDs Vu-Meter indicates the presence and level of audio signal.
A surveillance circuitry is continuously monitoring the temperature and the presence of AC and DC power supplies for both amplifiers. In case of a problem, the overload LEDs will be switched ON and the Fault relay will be activated.
The channels can be bridged together in order to create a single channel amplifier with twice the power.
• 2 audio outputs (100/70 / 8 Ohm outputs selectable)
• Fault reporting outputs
• Two audio inputs with gain-set
• Supervision of the amplifiers using DIVA8 or IDA8 controllers
• Advanced audio processing for each amplifier channel using DIVA8 or IDA8 systems
• Amplifier supervision and spare amplifier switching through DIVA8 or IDA8 systems
• Loudspeaker line and loudspeaker supervision through DIVA8 or IDA8 systems
Mains power supply
Voltage 230 VAC ±10%, 50/60 Hz
Power consumption** standby - idle* - Pmax
SPA 2120 28 W – 150 W – 322 W
* Idle: Measured with 10 Volt surveillance tone on the output.
**(Total Mains-power consumption)
Battery power supply
Voltage: 21-28 VDC
Power consumption** standby - idle* - Imax
SPA 2120 0.25 A – 2.9 A – 6.4 A
**(Per ch. @ 28 VDC)
*(Alarm cycle + 10 V pilot-tone @ 28 VDC)
Line inputs 2 x (One per channel)
Connector (electronically balanced): 3-pin XLR and 3-pin phoenix
Frequency response: +/-3 dB @ 40 Hz and 20 kHz
S/N: > 90 dBA
THD: < 1% @ 1 kHz
Input range: -6 dBV to 6 dBV / 770mV
Input impedance: 22 kOhm
Loudspeaker outputs SPA2120
Rated load resistance 100 Ohm (100 V); 50 Ohm (70 V)
Rated load capacitance 60 nF (100 V); 125 nF (70 V)
Rated output power (per channel) 120 W (cont. at 40°C)
Frequency response 40 Hz to 20 kHz(-3 dB)
S/N > 90 dB (no pilot tone)
Crosstalk < 80 dB at nominal load for 1 kHz
Distortion < 1% (@ 1 kHz) @ -10dB of rated output
Dimensions (H x W x D) for tabletop use,
with feet 92 x 440 x 305 mm
for 19” rack use,
with brackets 88 x 483 x 305 mm
SPA 2120 12,3 kg (27,1 lb)
Mounting Standalone or 19”-rackmount
Operating temperature -5 ºC to +55 ºC (+23 ºF to +131 ºF)
Storage temperature -40 ºC to +70 ºC (-40 ºF to +158 ºF)
Relative humidity 15% to 90%
Air pressure 600 to 1100 h Pa